Muscle mass Gains Injectable Anabolic Steroids yellow oil Oxandrolone 50 /

Muscle mass Gains use Injectable Anabolic Steroids yellow oil liquid of Oxandrolone 50 / Anavar 50 mg/ml for loss weight

Anavar 50mg/ml

Anavar Assay: 99.2%

Anavar Melting Point: 230~232 °C

Anavar Loss On Drying: 0.32%

Anavar Residue On Ignition: 0.06%

Anavar Melting Point: 230~232 °C

Anavar Standard: USP 32

Anavar Description:

Anavar also called Oxandrolone, is an oral steroid that is meant to be stacked with other muscle enhancing supplements such as Anadrol or Dianabol. While these are the two main steroids mentioned by the brand, any conventional testoster-one booster will help.

Despite being a relatively weak steroid, Anavar is still an effective option for massive muscle gains. The supplement is frequently used by some of the most successful athletes and bodybuilders in the industry. Most tablets come in 2.5 milligram form and to experience results, all you need is one to two supplements per day depending upon your body size. The dramatic results are better than most other supplements and you will end up very pleased if you do choose to stack Anavar with other options.

Anavar Usage

Anavar 50mg/ml is commonly used by bodybuilders, weightlifters and power-lifters. Weightlifters and power-lifters likes this steroid because Anavar causes fabulous gains in strength without gaining body weight. Its very important for them because they don want to end up in higher weight class.

Anavar 50mg/ml does not cause noticeable muscle growth and strength. It can be combined with many steroids, like Deca Durabolin, Dianabol and various testoster-one compounds. A combination that has been proven to be very effective is Anavar and Halotestin 20 - 30 mg per day. A good gain in muscle

mass and strength is 200 mg of Deca Durabolin every week, 500 mg of Test Enanthate per week and Anavar 25 mg daily.

Notes:

1. All steroid powders, oil and solvents used to make steroid injections are USP/BP standard .

2. We offer semi-finished steroid injections. You just need to buy some syringe filters

To filter it before injection. Heating semi-finished steroid injections in 70º C hot water for 30 mins will make

Filtering smoother.

How to make Anavar 50 Oil?

Step 1: Put Anavar powder into the beaker
Step 2: Put BA into the beaker
Step 3: Put BB into the beaker
Step 4: Put the beaker on the heater, temperature is about 80 ºC. Use the glass rod to stir the liquid until the powder dissolves into the liquid totally, then it will be transparent yellow liquid
Step 5: Get the beaker down from the heater, wait until the transparent yellow liquid is cool
Step 6: Put the EO into the beaker, Use the glass rod to stir the liquid until it is transparent yellow liquid again.
Step 7: Filter the liquid with a sterile filter or a filtering machine

How to prevent pain before inject?

1. Dilute compound with sterile cutting oil to get mg/ml at <=200 for long esters and <=100 for short esters.
2. Don bother with b-12, its water based-absorbed so quickly it will have little to no impact.
3. Gently warm the oil to improve viscosity. You could put the vial in the bathroom sink and let hot water run over the vial for 2 minutes, and shake well. This will lower the oils viscosity also making it easier it pull into the syringe.
4. Inject very slowly to reduce muscle fascia displacement, take 30 seconds per ml. Use a 25g pin to inject so it forces you to move slowly.
5. Add 20% Benzyl Benzoate by volume to propionate and phenylpropionate esetrs.
6. Use 23g needle to prevent high output pressure from smaller needles.
7. Inject frequently w/less volume, <3ml for large muscles and <2ml for smaller muscles.
8. Ensure that the injection is deep intra-muscular and fully through any sub cutaneous fat
9. You can also add: 100mg Benadryl one hour prior to injection; 800mg ibuprofen one hour prior to injection.

Contact info:

Smith Sun

Muscle mass Gains Injectable Anabolic Steroids yellow oil Oxandrolone 50 / Images